This the multi-page printable view of this section. Click here to print.

Return to the regular view of this page.

Installation

Installation options and instructions.

1 - Quick Start

Installing Kiali for demo or evaluation.

You can quickly install and try Kiali via one of the following two methods.

Install via Istio Addons

If you downloaded Istio, the easiest way to install and try Kiali is by running:

kubectl apply -f ${ISTIO_HOME}/samples/addons/kiali.yaml

To uninstall:

kubectl delete -f ${ISTIO_HOME}/samples/addons/kiali.yaml --ignore-not-found

Install via Helm

To install the latest version of Kiali Server using Helm, run the following command:

helm install \
  --namespace istio-system \
  --set auth.strategy="anonymous" \
  --repo https://kiali.org/helm-charts \
  kiali-server \
  kiali-server

To uninstall:

helm uninstall --namespace istio-system kiali-server

Access to the UI

Run the following command:

kubectl port-forward svc/kiali 20001:20001 -n istio-system

Then, access Kiali by visiting \https://localhost:20001/ in your preferred web browser.

2 - Installation Guide

Installing Kiali for production.

This section describes the production installation methods available for Kiali.

The recommended way to deploy Kiali is via the Kiali Operator, either using Helm Charts or OperatorHub.

The Kiali Operator is a Kubernetes Operator and manages your Kiali installation. It watches the Kiali Custom Resource (Kiali CR), a YAML file that holds the deployment configuration.

2.1 - Prerequisites

Hardware and Software compatibility and requirements.

Service Mesh Compatibility

Each Kiali release is tested against the most recent Istio release. In general, Kiali tries to maintain compatibility with older Istio releases and Kiali versions later than those posted in the below table may work, but such combinations are not tested and will not be supported. Known incompatibilities are noted in the compatibility table below.

Istio Version Compatibility

Istio
Kiali
Notes
1.11 1.38.1 or later
1.10 1.34.1 to 1.37.x
1.9 1.29.1 to 1.33.x
1.8 1.26.0 to 1.28.x Istio 1.8 removes all support for mixer/telemetry V1, as does Kiali 1.26.0. Use earlier versions of Kiali for mixer support.
1.7 1.22.1 to 1.25.x Istio 1.7 istioctl will no longer install Kiali. Use the Istio samples/addons all-in-one yaml or the Kiali Helm Chart for quick demo installs. Istio 1.7 is out of support.
1.6 1.18.1 to 1.21.x Istio 1.6 introduces CRD and Config changes, Kiali 1.17 is recommended for Istio < 1.6.


Maistra Version Compatibility

Maistra
SMCP CR
Kiali
Notes
2.0 2.0 1.24 Using Maistra 2.0 to install service mesh control plane 2.0 requires Kiali Operator v1.36. Other operator versions are not compatible.
2.0 1.1 1.12 Using Maistra 2.0 to install service mesh control plane 1.1 requires Kiali Operator v1.36. Other operator versions are not compatible.
1.1 1.1 1.12 Using Maistra 1.1 to install service mesh control plane 1.1 requires Kiali Operator v1.36. Other operator versions are not compatible.
n/a 1.0 n/a Service mesh control plane 1.0 is out of support.


Browser Version Requirements

Kiali requires a modern web browser and supports the last two versions of Chrome, Firefox, Safari or Edge.

Hardware Requirements

Any machine capable of running a Kubernetes based cluster should also be able to run Kiali.

However, Kiali tends to grow in resource usage as your cluster grows. Usually the more namespaces and workloads you have in your cluster, the more memory you will need to allocate to Kiali.

Platform-specific requirements

OpenShift

If you are installing on OpenShift, you must grant the cluster-admin role to the user that is installing Kiali. If OpenShift is installed locally on the machine you are using, the following command should log you in as user system:admin which has this cluster-admin role:

$ oc login -u system:admin

Google Cloud Private Cluster

Private clusters on Google Cloud have network restrictions. Kiali needs your cluster’s firewall to allow access from the Kubernetes API to the Istio Control Plane namespace, for both the 8080 and 15000 ports.

To review the master access firewall rule:

gcloud compute firewall-rules list --filter="name~gke-${CLUSTER_NAME}-[0-9a-z]*-master"

To replace the existing rule and allow master access:

gcloud compute firewall-rules update <firewall-rule-name> --allow <previous-ports>,tcp:8080,tcp:15000

2.2 - Install via Helm

Using Helm to install the Kiali Operator or Server.

Introduction

Helm is a popular tool that lets you manage Kubernetes applications. Applications are defined in a package named Helm chart, which contains all of the resources needed to run an application.

Kiali has a Helm Charts Repository at https://kiali.org/helm-charts. Two Helm Charts are provided:

  • The kiali-operator Helm Chart installs the Kiali operator which in turn installs Kiali when you create a Kiali CR.
  • The kiali-server Helm Chart installs a standalone Kiali without the need of the Operator nor a Kiali CR.

Although the kiali-server Helm Chart is actively maintained, it is only provided for convenience. The recommended method to install Kiali is by using the kiali-operator Helm Chart to install the Operator and then creating a Kiali CR to let the operator deploy Kiail.

Make sure you have the helm command available by following the Helm installation docs.

Adding the Kiali Helm Charts repository

Add the Kiali Helm Charts repository with the following command:

$ helm repo add kiali https://kiali.org/helm-charts

If you already added the repository, you may want to update your local cache to fetch latest definitions by running:

$ helm repo update

Installing Kiali using the Kiali operator

Once you’ve added the Kiali Helm Charts repository, you can install the latest Kiali Operator along with the latest Kiali server by running the following command:

$ helm install \
    --set cr.create=true \
    --set cr.namespace=istio-system \
    --namespace kiali-operator \
    --create-namespace \
    kiali-operator \
    kiali/kiali-operator

The --namespace kiali-operator and --create-namespace flags instructs to create the kiali-operator namespace (if needed), and deploy the Kiali operator on it. The --set cr.create=true and --set cr.namespace=istio-system flags instructs to create a Kiali CR in the istio-system namespace. Since the Kiali CR is created in advance, as soon as the Kiali operator starts, it will process it to deploy Kiali.

The Kiali Operator Helm Chart is configurable. Check available options and default values by running:

$ helm show values kiali/kiali-operator

The kiali-operator Helm Chart mirrors all settings of the Kiali CR as chart values that you can configure using regular --set flags. For example, the Kiali CR has a spec.namespace setting which you can configure in the kiali-operator Helm Chart by passing the --set cr.namespace flag as shown in the previous helm install example.

For more information about the Kiali CR, see the Creating and updating the Kiali CR page.

Operator-Only Install

To install only the Kiali Operator, omit the --set cr.create and --set cr.namespace flags of the helm command previously shown. For example:

$ helm install \
    --namespace kiali-operator \
    --create-namespace \
    kiali-operator \
    kiali/kiali-operator

This will omit creation of the Kiali CR, which you will need to create later to install Kiali Server. This option is good if you plan to do large customizations to the installation.

Installing Multiple Instances of Kiali

By installing a single Kiali operator in your cluster, you can install multiple instances of Kiali by simply creating multiple Kiali CRs. For example, if you have two Istio control planes in namespaces istio-system and istio-system2, you can create a Kiali CR in each of those namespaces to install a Kiali instance in each control plane.

If you wish to install multiple Kiali instances in the same namespace, or if you need the Kiali instance to have different resource names than the default of kiali, you can specify spec.deployment.instance_name in your Kiali CR. The value for that setting will be used to create a unique instance of Kiali using that instance name rather than the default kiali. One use-case for this is to be able to have unique Kiali service names across multiple Kiali instances in order to be able to use certain routers/load balancers that require unique service names.

Standalone Kiali installation

To install the Kiali Server without the operator, use the kiali-server Helm Chart:

$ helm install \
    --namespace istio-system \
    kiali-server \
    kiali/kiali-server

The kiali-server Helm Chart mirrors all settings of the Kiali CR as chart values that you can configure using regular --set flags. For example, the Kiali CR has a spec.server.web_fqdn setting which you can configure in the kiali-server Helm Chart by passing the --set server.web_fqdn flag as follows:

$ helm install \
    --namespace istio-system \
    --set server.web_fqdn=example.com \
    kiali-server \
    kiali/kiali-server

Upgrading Helm installations

If you want to upgrade to a newer Kiali version (or downgrade to older versions), you can use the regular helm upgrade commands. For example, the following command should upgrade the Kiali Operator to the latest version:

$ helm upgrade \
    --namespace kiali-operator \
    --reuse-values \
    kiali-operator \
    kiali/kiali-operator

WARNING: No migration paths are provided. However, Kiali is a stateless application and if the helm upgrade command fails, please uninstall the previous version and then install the new desired version.

Managing configuration of Helm installations

After installing either the kiali-operator or the kiali-server Helm Charts, you may be tempted to manually modify the created resources to modify the installation. However, we recommend using helm upgrade to update your installation.

For example, assuming you have the following installation:

$ helm list -n kiali-operator
NAME            NAMESPACE       REVISION        UPDATED                                 STATUS          CHART                   APP VERSION
kiali-operator  kiali-operator  1               2021-09-14 18:00:45.320351026 -0500 CDT deployed        kiali-operator-1.40.0   v1.40.0

Notice that the current installation is version 1.40.0 of the kiali-operator. Let’s assume you want to use your own mirrors of the Kiali Operator container images. You can update your installation with the following command:

$ helm upgrade \
    --namespace kiali-operator \
    --reuse-values \
    --set image.repo=your_mirror_registry_url/owner/kiali-operator-repo \
    --set image.tag=your_mirror_tag \
    --version 1.40.0 \
    kiali-operator \
    kiali/kiali-operator

Uninstalling

Removing the Kiali operator and managed Kialis

If you used the kiali-operator Helm chart, first you must ensure that all Kiali CRs are deleted. For example, the following command will agressively delete all Kiali CRs in your cluster:

$ kubectl delete kiali --all --all-namespaces

The previous command may take some time to finish while the Kiali operator removes all Kiali installations.

Then, remove the Kiali operator using a standard helm uninstall command. For example:

$ helm uninstall --namespace kiali-operator kiali-operator
$ kubectl delete crd kialis.kiali.io

Known problem: uninstall hangs (unable to delete the Kiali CR)

Typically this happens if not all Kiali CRs are deleted prior to uninstalling the operator. To force deletion of a Kiali CR, you need to clear its finalizer. For example:

$ kubectl patch kiali kiali -n istio-system -p '{"metadata":{"finalizers": []}}' --type=merge

Removing standalone Kiali

If you installed a standalone Kiali by using the kiali-server Helm chart, use the standard helm uninstall commands. For example:

$ helm uninstall --namespace istio-system kiali-server

2.3 - Install via OperatorHub

Using OperatorHub to install the Kiali Operator.

Introduction

The OperatorHub is a website that contains a catalog of Kubernetes Operators. Its aim is to be the central location to find Operators.

The OperatorHub relies in the Operator Lifecycle Manager (OLM) to install, manage and update Operators on any Kubernetes cluster.

The Kiali Operator is being published to the OperatorHub. So, you can use the OLM to install and manage the Kiali Operator installation.

Installing the Kiali Operator using the OLM

Go to the Kiali Operator page in the OperatorHub: https://operatorhub.io/operator/kiali.

You will see an Install button at the right of the page. Press it and you will be presented with the installation instructions. Follow these instructions to install and manage the Kiali Operator installation using OLM.

Afterwards, you can create the Kiali CR to install Kiali.

Installing the Kiali Operator in OpenShift

The OperatorHub is bundled in the OpenShift console. To install the Kiali Operator, simply go to the OperatorHub in the OpenShift console and search for the Kiali Operator. Then, click on the Install button and follow the instruction on the screen.

Afterwards, you can create the Kiali CR to install Kiali.

2.4 - The Kiali CR

Creating and updating the Kiali CR.

The Kiali Operator watches the Kiali Custom Resource (Kiali CR), a YAML file that holds the deployment configuration. Creating, updating, or removing a Kiali CR will trigger the Kiali Operator to install, update, or remove Kiali.

The Operator provides comprehensive defaults for all properties of the Kiali CR. Hence, the minimal Kiali CR does not have a spec:

apiVersion: kiali.io/v1alpha1
kind: Kiali
metadata:
  name: kiali

Assuming you saved the previous YAML to a file named my-kiali-cr.yaml, and that you are installing Kiali in the same default namespace as Istio, create the resource with the following command:

$ kubectl apply -f my-kiali-cr.yaml -n istio-system

Once created, the Kiali Operator should shortly be notified and will process the resource, performing the Kiali installation. You can check installation progress by inspecting the status attribute of the created Kiali CR:

$ kubectl describe kiali -n istio-system
Name:         kiali
Namespace:    istio-system
Labels:       <none>
Annotations:  <none>
API Version:  kiali.io/v1alpha1
Kind:         Kiali

  (...some output is removed...)

Status:
  Conditions:
    Last Transition Time:  2021-09-15T17:17:40Z
    Message:               Running reconciliation
    Reason:                Running
    Status:                True
    Type:                  Running
  Deployment:
    Instance Name:  kiali
    Namespace:      istio-system
  Environment:
    Is Kubernetes:       true
    Kubernetes Version:  1.21.2
    Operator Version:    v1.40.0
  Progress:
    Duration:  0:00:16
    Message:   5. Creating core resources
Events:        <none>

We recommended to download the example Kiali CR YAML file that is available in the Operator’s GitHub repository. This example file contains and describes all available settings. Then, edit the downloaded file being very careful to maintain proper formatting. Incorrect indentation is a common problem!

Once you created a Kiali CR, you can manage your Kiali installation by editing the resource using the usual Kubernetes tools:

$ kubectl edit kiali kiali -n istio-system

2.5 - Accessing Kiali

Accessing and exposing the Kiali UI.

Introduction

After Kiali is succesfully installed you will need to make Kiali accessible to users. This page describes some popular methods of exposing Kiali for use.

If exposing Kiali in a custom way, you may need to set some configurations to make Kiali aware of how users will access Kiali.

Accessing Kiali using port forwarding

You can use port-forwarding to access Kiali by running any of these commands:

# If you have oc command line tool
oc port-forward svc/kiali 20001:20001 -n istio-system
# If you have kubectl command line tool
kubectl port-forward svc/kiali 20001:20001 -n istio-system

These commands will block. Access Kiali by visiting \https://localhost:20001/ in your preferred web browser.

Accessing Kiali through an Ingress

By default, the installation exposes Kiali creating an Ingress resource. Find out your Ingress IP or domain name and use it to access Kiali by visiting this URL in your web browser: https://_your_ingress_ip_or_domain_/kiali.

To find your Ingress IP or domain name, as per the Kubernetes documentation, try the following command (doesn’t work if using Minikube):

kubectl get ingress kiali -n istio-system -o jsonpath='{.status.loadBalancer.ingress[0].ip}'

If it doesn’t work, unfortunately, it depends on how and where you had setup your cluster. There are several Ingress controllers available and some cloud providers have their own controller or preferred exposure method. Please, check the documentation of your cloud provider. You may need to customize the pre-installed Ingress rule, or to expose Kiali using a different method.

Customizing the Ingress resource

By default, a catch-all Ingress resource is created to route traffic to Kiali. Most likely, you will need a more specific Ingress resource that routes traffic to Kiali only on a specific domain or path. To do this, you can specify route settings.

Alternatively, and for more advanced Ingress configurations, you can provide your own Ingress declaration in the Kiali CR. For example:

spec:
  deployment:
    override_ingress_yaml:
      metadata:
        annotations:
          nginx.ingress.kubernetes.io/secure-backends: "true"
          nginx.ingress.kubernetes.io/backend-protocol: "HTTPS"
      spec:
        rules:
        - http:
            paths:
            - path: /kiali
              backend:
                serviceName: kiali
                servicePort: 20001

Accessing Kiali in Minikube

If you [enabled the Ingress controller]https://kubernetes.io/docs/tasks/access-application-cluster/ingress-minikube/#enable-the-ingress-controller, the default Ingress resource created by the installation (mentioned in the previous section) should be enough to access Kiali. The following command should open Kiali in your default web browser:

xdg-open https://$(minikube ip)/kiali

Accessing Kiali through a LoadBalancer or a NodePort

By default, the Kiali service is created with the ClusterIP type. To use a LoadBalancer or a NodePort, you can change the service type in the Kiali CR as follows:

spec:
  deployment:
    service_type: LoadBalancer

Once the Kiali operator to updates the installation, you should be able to use the kubectl get svc -n istio-system kiali command to retrieve the external address (or port) to access Kiali. For example, in the following output Kiali is assigned the IP 192.168.49.201, which means that you can access Kiali by visiting \http://192.168.49.201:20001 in a browser:

NAME    TYPE           CLUSTER-IP       EXTERNAL-IP      PORT(S)                          AGE
kiali   LoadBalancer   10.105.236.127   192.168.49.201   20001:31966/TCP,9090:30128/TCP   34d

Accessing Kiali through an Istio Ingress Gateway

If you want to take advantage of Istio’s infrastructure, you can expose Kiali using an Istio Ingress Gateway. The Istio documentation provides a good guide explaining how to expose the sample add-ons. Even if the Istio guide is focused on the sample add-ons, the steps are the same to expose a Kiali installed using this Installation guide.

Accessing Kiali in OpenShift

By default, installation exposes Kiali through a Route. The following command should open Kiali in your default web browser:

xdg-open https://$(oc get routes -n istio-system kiali -o jsonpath='{.spec.host}')/console

Specifying route settings

Either if you are using your own exposure method, or if you are using one of the methods mentioned in this page, you may need to configure the route that is being used to access Kiali.

In the Kiali CR, route settings are broken in several attributes. For example, to specify that Kiali is being accessed under the \https://apps.example.com:8080/dashboards/kiali URI, you would need to set the following:

spec:
  server:
    web_fqdn: apps.example.com
    web_port: 8080
    web_root: /dashboards/kiali
    web_schema: https

If you are letting the installation to create an Ingress resource for you, the Ingress will be adjusted to match these route settings. If you are using your own exposure method, this is only making Kiali aware about what is its public endpoint.

It is possible to omit these settings and Kiali may be able to discover some of these configurations, depending on your exposure method. For example, if you are exposing Kiali via LoadBalancer or NodePort service types, Kiali can discover most of these settings. If you are using some kind of Ingress, Kiali will honor X-Forwarded-Proto, X-Forwarded-Host and X-Forwarded-Port HTTP headers if they are properly injected in the request.

The web_root receives special treatment, because this is the path where Kiali will serve itself (both the user interface and its api). This is useful if you are serving multiple applications under the same domain. It must begin with a slash and trailing slashes must be omitted. The default value is /kiali for Kubernetes and / for OpenShift.

Configuring listening ports

It is possible to configure the listening ports of the Kiali service to use your preferred ones:

spec:
  server:
    port: 80 # Main port for accessing Kiali
    metrics_port: 8080

2.6 - Advanced Install

Advanced installation options.

Multiple Istio control planes in the same cluster

Currently, Kiali can manage only one Istio control plane. However, there are certain cases where you may have more than one Istio control plane in your cluster. One of such cases is when performing a Canary upgrade of Istio.

In these cases, you will need to configure in Kiali which control plane you want to manage. This is done by configuring the name of the components of the control plane. This is configured in the Kiali CR and the default values are the following:

spec:
  external_services:
    istio:
      config_map_name: "istio"
      istiod_deployment_name: "istiod"
      istio_sidecar_injector_config_map_name: "istio-sidecar-injector"

If you want to manage both Istio control planes, simply install two Kiali instances and point each one to a different Istio control plane.

Installing a Kiali Server of a different version than the Operator

When you install the Kiali Operator, it will be configured to install a Kiali Server that is the same version as the operator itself. For example, if you have Kiali Operator v1.34.0 installed, that operator will install Kiali Server v1.34.0. If you upgrade (or downgrade) the Kiali Operator, the operator will in turn upgrade (or downgrade) the Kiali Server.

There are certain use-cases in which you want the Kiali Operator to install a Kiali Server whose version is different than the operator version. Read the following section «Using a custom image registry» section to learn how to configure this setup.

Using a custom image registry

Kiali is released and published to the Quay.io container image registry. There is a repository hosting the Kiali operator images and another one for the Kiali server images.

If you need to mirror the Kiali container images to some other registry, you still can use Helm to install the Kiali operator as follows:

$ helm install \
    --namespace kiali-operator \
    --create-namespace \
    --set image.repo=your.custom.registry/owner/kiali-operator-repo
    --set image.tag=your_custom_tag
    --set allowAdHocKialiImage=true
    kiali-operator \
    kiali/kiali-operator

Then, when creating the Kiali CR, use the following attributes:

spec:
  deployment:
    image_name: your.custom.registry/owner/kiali-server-repo
    image_version: your_custom_tag

Development Install

This option installs the latest Kiali Operator and Kiali Server images which are built from the master branches of Kiali GitHub repositories. This option is good for demo and development installations.

helm install \
  --set cr.create=true \
  --set cr.namespace=istio-system \
  --set cr.spec.deployment.image_version=latest \
  --set image.tag=latest \
  --namespace kiali-operator \
  -- create-namespace \
  kiali-operator \
  kiali/kiali-operator

2.7 - Example Install

Installing two Kiali servers via the Kiali Operator.

This is a quick example of installing Kiali. This example will install the operator and two Kiali Servers - one server will require the user to enter credentials at a login screen in order to obtain read-write access and the second server will allow anonymous read-only access.

For this example, assume there is a Minikube Kubernetes cluster running with an Istio control plane installed in the namespace istio-system and the Istio Bookinfo Demo installed in the namespace bookinfo:

$ kubectl get deployments.apps -n istio-system
NAME                   READY   UP-TO-DATE   AVAILABLE   AGE
grafana                1/1     1            1           8h
istio-egressgateway    1/1     1            1           8h
istio-ingressgateway   1/1     1            1           8h
istiod                 1/1     1            1           8h
jaeger                 1/1     1            1           8h
prometheus             1/1     1            1           8h

$ kubectl get deployments.apps -n bookinfo
NAME             READY   UP-TO-DATE   AVAILABLE   AGE
details-v1       1/1     1            1           21m
productpage-v1   1/1     1            1           21m
ratings-v1       1/1     1            1           21m
reviews-v1       1/1     1            1           21m
reviews-v2       1/1     1            1           21m
reviews-v3       1/1     1            1           21m

Install Kiali Operator via Helm Chart

First, the Kiali Operator will be installed in the kiali-operator namespace using the operator helm chart:

$ helm repo add kiali https://kiali.org/helm-charts
$ helm repo update kiali
$ helm install \
    --namespace kiali-operator \
    --create-namespace \
    kiali-operator \
    kiali/kiali-operator

Install Kiali Server via Operator

Next, the first Kiali Server will be installed. This server will require the user to enter a Kubernetes token in order to log into the Kiali dashboard and will provide the user with read-write access. To do this, a Kiali CR will be created that looks like this (file: kiali-cr-token.yaml):

apiVersion: kiali.io/v1alpha1
kind: Kiali
metadata:
  name: kiali
  namespace: istio-system
spec:
  auth:
    strategy: "token"
  deployment:
    accessible_namespaces: ["bookinfo"]
    view_only_mode: false
  server:
    web_root: "/kiali"

This Kiali CR will command the operator to deploy the Kiali Server in the same namespace where the Kiali CR is (istio-system). The operator will configure the server to: respond to requests to the web root path of /kiali, enable read-write access, use the authentication strategy of token, and be given access to the bookinfo namespace:

$ kubectl apply -f kiali-cr-token.yaml

Get the Status of the Installation

The status of a particular Kiali Server installation can be found by examining the status field of its corresponding Kiali CR. For example:

$ kubectl get kiali kiali -n istio-system -o jsonpath='{.status}'

When the installation has successfully completed, the status field will look something like this (when formatted):

$ kubectl get kiali kiali -n istio-system -o jsonpath='{.status}' | jq
{
  "conditions": [
    {
      "ansibleResult": {
        "changed": 21,
        "completion": "2021-10-20T19:17:35.519131",
        "failures": 0,
        "ok": 102,
        "skipped": 90
      },
      "lastTransitionTime": "2021-10-20T19:17:12Z",
      "message": "Awaiting next reconciliation",
      "reason": "Successful",
      "status": "True",
      "type": "Running"
    }
  ],
  "deployment": {
    "accessibleNamespaces": "bookinfo,istio-system",
    "instanceName": "kiali",
    "namespace": "istio-system"
  },
  "environment": {
    "isKubernetes": true,
    "kubernetesVersion": "1.20.2",
    "operatorVersion": "v1.41.0"
  },
  "progress": {
    "duration": "0:00:20",
    "message": "7. Finished all resource creation"
  }
}

Access the Kiali Server UI

The Kiali Server UI is accessed by pointing a browser to the Kiali Server endpoint and requesting the web root /kiali:

xdg-open http://$(minikube ip)/kiali

Because the auth.strategy was set to token, that URL will display the Kiali login screen that will require a Kubernetes token in order to authenticate with the server. For this example, you can use the token that belongs to the Kiali service account itself:

$ kubectl get secret -n istio-system $(kubectl get sa kiali-service-account -n istio-system -o jsonpath='{.secrets[0].name}') -o jsonpath='{.data.token}' | base64 -d

The output of that command above can be used to log into the Kiali login screen.

Install a Second Kiali Server

The second Kiali Server will next be installed. This server will not require the user to enter any login credentials but will only provide a view-only look at the service mesh. To do this, a Kiali CR will be created that looks like this (file: kiali-cr-anon.yaml):

apiVersion: kiali.io/v1alpha1
kind: Kiali
metadata:
  name: kiali
  namespace: kialianon
spec:
  installation_tag: "Kiali - View Only"
  istio_namespace: "istio-system"
  auth:
    strategy: "anonymous"
  deployment:
    accessible_namespaces: ["bookinfo"]
    view_only_mode: true
    instance_name: "kialianon"
  server:
    web_root: "/kialianon"

This Kiali CR will command the operator to deploy the Kiali Server in the same namespace where the Kiali CR is (kialianon). The operator will configure the server to: respond to requests to the web root path of /kialianon, disable read-write access, not require the user to authenticate, have a unique instance name of kialianon and be given access to the bookinfo namespace. The Kiali UI will also show a custom title in the browser tab so the user is aware they are looking at a “view only” Kiali dashboard. The unique deployment.instance_name is needed in order for this Kiali Server to be able to share access to the Bookinfo application with the first Kiali Server.

$ kubectl create namespace kialianon
$ kubectl apply -f kiali-cr-anon.yaml

The UI for this second Kiali Server is accessed by pointing a browser to the Kiali Server endpoint and requesting the web root /kialianon. Note that no credentials are required to gain access to this Kiali Server UI because auth.strategy was set to anonymous; however, the user will not be able to modify anything via the Kiali UI - it is strictly “view only”:

xdg-open http://$(minikube ip)/kialianon

Reconfigure Kiali Server

A Kial Server can be reconfigured by simply editing its Kiali CR. The Kiali Operator will perform all the necessary tasks to complete the reconfiguration and reboot the Kiali Server pod when necessary. For example, to change the web root for the Kiali Server:

$ kubectl patch kiali kiali -n istio-system --type merge --patch '{"spec":{"server":{"web_root":"/specialkiali"}}}'

The Kiali Operator will update the necessary resources (such as the Kiali ConfigMap) and will reboot the Kiali Server pod to pick up the new configuration.

Uninstall Kiali Server

To uninstall a Kiali Server installation, simply delete the Kiali CR. The Kiali Operator will then perform all the necessary tasks to remove all remnants of the associated Kiali Server.

kubectl delete kiali kiali -n istio-system

Uninstall Kiali Operator

To uninstall the Kiali Operator, use helm uninstall and then manually remove the Kiali CRD.

$ kubectl delete kiali --all --all-namespaces
$ helm uninstall --namespace kiali-operator kiali-operator
$ kubectl delete crd kialis.kiali.io